Simulating various patterns of muscle co-contraction to move the knee

Now that the femur of your knee kit is fixed in place, you're ready to start simulating various patterns of muscle contraction to see these affect the knee joint and the motion of the tibia.

An extensor contracting on its own

How to attach a manual muscle cord to a tendon clip

You'll start by simulating the contraction of a single muscle on its own to see what happens when muscles don't co-contract (also called co-activate) with other muscles, using the rectus femoris muscle as an example. This muscle is one of the four quadriceps muscles (rectus femoris, vastus lateralis, vastus medialis, and vastus intermedius), which are knee extensor muscles (they extend the knee). To attach the rectus femoris manual muscle cord, follow the steps shown in the video or listed out below.

Video to add: Attaching a manual muscle cord from CS plate to REF clip

Thread the non-looped end of a manual muscle cord through the attachment site for rectus femoris in the cross section plate (labeled REF-A).
Image to add
Pull the cord through enough so that you can insert the non-looped end of the cord through the clip on the rectus femoris portion of the patellar tendon (labeled REF-B). Be sure to insert the cord through the labeled side first (i.e., you should see "REF-B" as you're inserting the cord).
Image to add
Pull the end knot through the clip and slide the cord into the slot on the top of the clip.
Image to add
Pull the cord back through the clip in the opposite direction, keeping the cord in the slot and allowing the knot to get become hooked inside the clip.
Image to add

Simulating muscle contraction

To simulate the contraction and shortening of the rectus femoris, pull on the looped end of the cord. Simulate shortening of the rectus femoris a few times. Get a feel for the range of flexion and extension you can achieve and how well you can control the motion.

Image to add: two images, one with cord tight and one with cord pulled and knee extended

Whenever you're pulling manual muscle cords through the cross section plate, pull directly backward (not upward). If you pull upward, the cord will pull up on the cross section plate, possibly lifting it out of the bracket.

Image to add: hand pulling on cord, arrows indicating to pull backward not upward

What's the problem with using a single muscle to move a bone? Write your answer on page 1 of the activity worksheet.

Two muscles driving motion

In the previous simulation, your rectus femoris acted as an agonist (a muscle whose contraction moves a part of the body). However, you should have noticed a problem with controlling the motion using just one muscle. What you need to fix this problem is a second muscle that acts in opposition to the agonist: an antagonist; together, these form an agonist-antagonist pair. The primary muscles acting in opposition to the quadriceps (extensors) are the hamstrings: the semimembranosus, semitendinosus, and the biceps femoris. The hamstring muscles are knee flexors (they flex the knee). Attach a second manual muscle cord to your knee kit representing the semimembranosus, using the instructions below.

How to attach a manual muscle cord to a bone

To attach a manual muscle cord to a bone, follow the steps shown in the video or listed out below.

Video to add: Attaching a manual muscle cord from the CS plate to a bone (e.g., semimembranosus)

Thread the non-looped end of a manual muscle cord through the attachment site for semimembranosus in the cross section plate (labeled SEM-A) and pull the cord through, just as you did for the rectus femoris.
Image to add
Use the forceps to push the knot (again at the non-looped end of the cord) into the semimembranosus attachment hole on the tibia (labeled SEM-B). The knot should be pushed fully below the surface of the bone, into the hole.
Image to add
Pull the cord into the slot of the hole until the knot is caught by the hook inside the hole and the cord is secured (you may feel the knot "click" into place). You might need to hold the knot inside the hole with the forceps while pulling on the cord to keep it in until it locks into place.
Image to add
Leave the "tail" after the knot sticking out of the hole to make it easier to remove the cord later.
Image to add

Whenever you're attaching a muscle to your knee kit, be sure that the two attachment sites have the same 3-letter muscle code, indicating they belong to the same muscle. For example, when you attached the rectus femoris from/through the cross section plate to the patellar tendon, both of these sites had the 3-letter code "REF," indicating that both are rectus femoris attachment sites. The sites will have different letters after the three letters (e.g., REF-A, REF-B, etc.); these letters indicate different sites for the same muscle. If you attach a muscle to sites with two different 3-letter codes, you're creating a muscle that doesn't exist. Is that fun? Yes, of course. But it's not within the scope of this activity.

Now that you have both manual muscle cords attached, simulate co-contraction of the rectus femoris and semimembranosus to rotate the knee through flexion and extension.

Video of co-contraction of REF and SEM

Based on your simulation, why do you think at least two muscles are needed to drive smooth, controlled motion? And why is muscle coordination (regulating the timing and force of muscles relative to other muscles) important when co-contracting multiple muscles (i.e., why can't you just contract all muscles with equal tension at the same time)? Write your answers on page 1 of the activity worksheet; check the hint below if you need some help.

HINT

In considering the importance of muscle coordination, pay attention to the relative timing and force you're using with your hands as you pull the two muscle cords to simulate flexion and extension.

How to detach a manual muscle cord

For the next simulation, you'll need to detach the rectus femoris and semimembranosus from your knee. To detach a muscle cord, follow the steps shown in the video or listed out below.

Video to add: Detaching the rectus femoris manual muscle cord from the tendon clip and detaching the semimembranosus muscle from the bone

To detach the rectus femoris from its attachment to the tendon clip, pull the cord up and out of the slot. The knot will then be free to pull through the clip and you can remove the muscle cord out through the cross section plate.
Image to add
To detach the semimembranosus from its bony attachment to the tibia, pull the cord so that it slides out of the slot portion of the hole. It can be helpful to use the forceps for this.
Image to add
Pull the "tail" of the cord sticking out from the hole until the knot and cord pull out of the hole and then remove the muscle cord out through the cross section plate.
Image to add

Two extensors driving motion

A co-contracting muscle pair doesn't have to consist of an extensor and flexor (i.e., muscles on opposite sides of a joint). Motion and stability at a joint can benefit from the co-contraction of multiple muscles on the same side of a joint. To figure out why, use your knee kit to simulate the following patterns of muscle contraction, using two additional quadriceps muscles as an example:

Simulate the vastus lateralis contracting on its own to extend the knee. Attach the vastus lateralis by threading it through any of its attachment sites on the cross section plate (labeled VAL-A, VAL-B, or VAL-C) and clipping it into the vastus lateralis portion of the patellar tendon (labeled VAL-D).
Simulate the vastus lateralis and vastus medialis co-contracting to extend the knee. Attach the vastus medialis by threading it through its attachment site on the cross section plate (labeled VAM-A) and clipping it into the vastus lateralis portion of the patellar tendon (labeled VAM-D).

Note, that in a real knee, the muscles and tendinous sheath surrounding the patella (not all of which is represented in your knee kit) all have some passive tension that holds the patella in place as long as there aren't any high forces acting on it; the patella wouldn't just flop forward or over to the side as it does in your knee kit. What you want to pay attention to is what happens to the knee (including the patella) when you are actively pulling the manual muscle cords and their resulting lines of action; that is properly represented in your model.

Based on your simulations, what's the problem with only contracting the vastus lateralis? Why is it beneficial (for knee function and stability) to co-contract the vastus lateralis and medialis and how does this relate to patellar tracking disorders (the deviation of the patella from its proper groove during knee motion)? Do you think this pattern of two muscles on the same "side" of a joint co-contracting is a common one for joints, beyond just the knee joint? If yes, why? If no, why not? Write your answers on page 2 of the activity worksheet; check the hint below if you need some help.

HINT

The ligaments that hold joints together can be damaged by excessive torques that would move the joint in abnormal ways. Additionally, some joints allow for a wide range of motions/rotations (e.g., the shoulder), which means that the muscles can't rely as much on ligaments to guide motion along a particular axis.

Two flexors driving motion

SEM

SEM+BFE

An agonist-antagonist pair stiffening a joint

SEM

Two agonist-antagonist pairs stiffening a joint

SEM